Starbar® Silicon Carbide
SiC Heating Elements
Moly-D Molybdenum Disilicide
MoSi2 Heating Elements
Starbar® & Moly-D® Heating Elements
Starbar Silicon Carbide SiC Heating Elements
Type DB Dumbbell and TDB Tubular Dumbbell - (Enlarged Cold End) - Silicon Carbide Heating Elements
Item # DB-0.31-8
Email This Page
Save To Favorites
Item # DB-0.31-8, Type DB Dumbbell - (Enlarged Cold End) - Silicon Carbide Heating Element
One of the earliest heating element designs, the enlarged cold ends of the Dumbbell style element were originally made oversized to increase cold end cross section, lowering electrical resistance, thereby lowering cold end operating temperature. Modern Dumbbell Starbars, by contrast, employ an advanced technology to keep the terminal ends cool by virtue of the decreased resistivity of the lower resistance cold end material used in the manufacturing process. Oversize cold ends are therefore no longer necessary. Non-dumbbell (RR Starbars) can be substituted for Dumbbell Starbars. Improvements in the cold-end-to-hot-zone resistance ratio between the original DB and new DB Starbar have been dramatic. The old style resistance ratio was 1:3, whereas the new DB and RR resistance ratio is a minimum of 1:15.
The first several inches of the cold ends are metalized with aluminum to provide a low-resistance contact surface. Electrical connections are made using flat aluminum braids, held in compression to the cold end circumference by stainless steel spring clamps.
DB Starbars are described by giving the overall length, the heating section length, the hot zone outer diameter and the cold end outer diameter.
As an example, DB 22 x 15 x .31/.50 is a Dumbbell Starbar 22 inches long, 15 inch hot zone, .31 hot zone OD and .50 cold end OD. In millimeters the part number would be DB 560 x 380 x 8/14.
For sizes available, please refer to Table B, DB Starbar Dimensions.
With a larger diameter, thinner wall, and clear inner diameter (ID) the TDB are used as tube heaters. An electrically insulative load tube, usually made of mullite, can be used to isolate the product from the TDB Starbar. The surface of Starbars are electrically live. See Table B, for the ID dimensions and recommended load tube diameters.
Hot Zone Outer Diameter
Cold End Outer Diameter
DB Starbars can operate to furnace temperatures up to 2730ºF (1500ºC). If the furnace temperature is to be 2600ºF (1425ºC) or above, the terminal end or cold end should be well protected within the refractory wall of the furnace. The hot zone material is rated to furnace temperatures up to 3100ºF (1700ºC).
The maximum operating temperature should be reduced for non-air applications with the exception of argon and helium that can be used without any reduction. Reducing atmospheres, such as hydrogen or disassociated ammonia, particularly with low dew-points, may remove the protective silicon oxide protection that forms on silicon carbide. In such atmospheres, temperature reductions are required as shown in Figure 1.
The maximum furnace temperature for a nitrogen atmosphere is 2500ºF (1370ºC) with a watt loading of 20 w/in
to 30 w/in
to 4.6 w/cm
) maximum watt surface watt loading. Too high a surface temperature will result in formation of silicon nitride causing a thermally insulative layer to form around the Starbar resulting in over-temperature damage.
Hot Zone (Electrical Resistance)
Cold End (Electrical Resistance)
Maximum Heating Length
Maximum Overall Length
, T - Type Terminal Clamp
, T - Type Terminal Clamp
A 2.4 gm-cc density helps prevent the crystalline lattice structure from being oxidized, resulting in a very slow aging characteristic.
Starbars are interchangeable with all dumbbell silicon carbide heating elements manufactured in the United States as well as higher resistance heating elements manufactured for the Asian and European markets. It is important to provide the nominal electrical resistance when ordering Starbars.
The silicon carbide Starbar is a linear type resistance heater that converts electrical energy to heat energy - Joule's Law W = I
x R, (W = power in watts, I = current in amperes, R = resistance on ohms).
DB Starbars have a negative res
Starbars are not sized to a specific wattage output like metallic heating elements. The amount of energy that a Starbar is capable of converting from electrical to heat energy depends on the ambient furnace temperature and atmosphere in which the Starbar
Ease of Replacement
DB Starbars can be replaced while the furnace is at operating temperature. The power to the Starbars being changed should be shut off, the spring clips and aluminum braid released, and the old Starbar removed. The new Starbar should be inserted smoothly through the hot furnace with sufficient speed to insure that the aluminum is not melted off the terminal end but not so fast as to cause thermal shock.
Starbars increase gradually in resistance with use. This characteristic of increasing in resistance is called aging. Aging is a function of the following:
Electrical loading - usually expressed in watts per square inch or watts per square centimeter of Starbar radiating surface
Type of operation (continuous or intermittent)
Operating and maintenance techniques
DB Starbars can be mounted in any orientation. Holes through refractory walls or in ceramic lead-in sleeves, if used, must be large enough to ensure no physical binding of the Starbars. The alignment of the support holes through refractory walls should also guarantee that no physical binding occurs.
If ceramic fiber bulk is used to help reduce radiant energy losses around the Starbars, it must be tucked gently around the diameter of the cold end for a distance of only 12 mm (1/2 inch). The ceramic fiber should never be packed so tightly that it restricts the thermal expansion differences between the Starbar and furnace components. Aluminum braid should be kept slack so that there is no physical stress being applied to the Starbars.
Recommended Minimum Refractory Hole Size
Minimum Hole Diameter Based on Refractory Wall Thickness
Cold End Outer Diameter
Starbars can be shipped from stock or two to three weeks after receipt of an order.
Specifications and Matching
Starbars have a manufactured tolerance of plus or minus 20% on the nominal resistance. All Starbars are calibrated at least twice prior to shipping to ensure their being within specifications. The calibrated amperage of each Starbar is marked on the carton and right hand end of each Starbar. When installing, arrange Starbars with amperage values as close to each other as available. Longer service life will be obtained when series connected Starbars are matched in resistance. Starbars are shipped as closely matched as possible.
Furnace Heating Chamber
The furnace heated chamber dimension, which the Starbar spans, can be the same as the Starbar (as shown by the Starbars under the load in Figure 3). Recommended terminal hole diameters for various refractory walls and Starbar sizes are shown in Table C.
Starbars should not be placed closer than two Starbar diameters to each other or one and one half Starbar diameter to a wall or other reflecting body. If the Starbar is not able to dissipate heat energy equally in all directions, it may cause local overheating and possible failure.
The formula for computing the recommended Starbar spacing to obtain an even temperature gradient on the product being heated is shown in Figure 3.
Held in place by clamps, braided aluminum terminal straps in 25, 50, 100, and 200 ampere ratings, are available in two primary styles: Single Loop (for connecting binding post to element) and Double Loop (for connecting element to element). Post to Post straps are also available. Detailed descriptions and part numbers can be found in our accessory literature.
There are two type of clamps: Type "M" (derives its name from its similarity to the letter M) and Type "T" (used with a tool). Please refer to our accessory literature for a detailed part number and description.
DB Starbar Spacing
X = 2 x Starbar hot zone diameter is the minimum, 1.5 x Starbar hot zone diameter is the absolute minimum and requires a reduced Starbar Surface Watt Loading.
Z = S ÷ 1.73 minimum for moving loads
S = 2 x Starbar hot zone diameter minimum
X - distance from the centerline of Starbar to any reflecting surface, such as a refractory wall or product
Z - distance from the centerline of the Starbar to a moving or stationary load
S - distance from centerline of the Starbar to the centerline of an adjacent Starbar
Type DB Dumbbell - (Enlarged Cold End) - Silicon Carbide Heating Element
I Squared R Element Co., Inc. 12600 Clarence Center Road, Akron, NY 14001
Ph: 716.542.5511 Fx: 716.542.2100 Email:
We make deliveries all over the world
Site created by
Thomas Web Solutions
and powered by